300-615 DCIT CCNP Data Center Updated Questions Available

dumps2022-08-23T02:15:02+08:00

Cisco 300-615 DCIT exam updated questions are available, which are useful for you to earn CCNP Data Center certification. All the Cisco certification 300-615 DCIT exam questions and answers are proved to be valid among those Cisco candidates. Free updated CCNP Data Center 300-615 DCIT exam questions are available.

Page 1 of 6

1. Refer to the exhibit.

A network engineer upgrades the firmware of a Cisco Fabric Interconnect from boot flash. During the process, the fabric interconnect reboots and displays the message shown in the exhibit .

Which action resolves the issue?

Remove the service pack and upgrade through the auto-install procedure

Reset the I/O module and install the firmware image from the boot flash

Boot the kickstart image from boot flash and load the system image

Reload the switch and boot the kickstart image from the TFTP server

2. An engineer is troubleshooting a failed DCBX exchange between a server and a Cisco Nexus switch .

Which action allows DCBX to successfully negotiate?

Enable ETS

Enable PF

Enable Cisco Discovery Protocol.

Enable LLD

3. A network engineer discovers a DNS resolution problem on a device that is using the Cisco Nexus Bash shell.

The device name is app with an IP address of 10.10.10.1. The primary server IP address is 172.16.10.1 and the secondary server IP address is 172.16.10.2. When the abc.com resolution fails, it should attempt to use efg.com .

Which settings must be added to resolv.conf file to resolve the issue?

Option A

Option B

Option D

4. Refer to the exhibit.

During implementation of a Cisco UCS C-Series Server, an engineer receives the status that is shown in the exhibit .

Which action resolves the issue.

Reconfigure the Drive Type from "Removable" to "Non-Removable"

Insert an SD card into SLOT-2

Configure the RAID that is associated with the card.

Set SLOT-1 Sync Mode to "Auto"

5. Refer to the exhibit.

One of the vPC VTEPs fails to route VXLAN traffic to vPC connected hosts. When the issue was being diagnosed, it was discovered that the packets that were expected to be forwarded to the MAC address on the SWITCH-VTEP-1 are instead forwarded to the MAC address on SWITCH-VTEP-2 and then dropped .

Which action resolves the issue?

Configure a distributed anycast gateway on both peers

Configure ip arp synchronize under the VPC domain on both peers

Configure peer-gateway under the VPC domain on both peers

Configure a different secondary IP address for one of the vPC peers

6. Refer to the exhibit.

When an engineer inserts 8-Gb FC SFP port 15 on a Cisco UCS Fabric Interconnect, the port fails .

What is a possible cause of the issue?

Port 15 is configured as an Ethernet port.

Port 15 is configured for 4-Gb F

Port 15 is missing a license.

The polarity of the fiber cable is reversed.

7. A system administrator adds two vNICs to an existing service profile that is used to run a vSphere environment to support disjoint Layer 2 network connectivity. However, after the server is rebooted, the host is not accessible on the network.

Which action resolves the issue?

Remove all existing vNICs and add them in the desired order.

Build a new service profile with the desired network configuration

Add the disjoint Layer 2 VLANs to an existing vNIC rather than adding new vNICs

Create a vNIC placement policy to avoid adapter renumbering

8. A network engineer is implementing the Cisco ACI Fabric and notices that the Leaf-1 switch is registered, has an assigned name, but is displayed as inactive in the APIC. After further investigation, it became clear that the leaf switch was recently moved from another Cisco ACI environment .

Which action resolves the problem?

Clean reload the Leaf-1 switch

Define the new TEP address for Leaf-1

Change the clock offset from low to high between apic 1 and Leaf-1

Modify the ISIS interface peering IP address between apic 1 and Leaf-1

9. An engineer enables the packet postcards feature on a Cisco Nexus 9000 Series Switch but receives the error message "Error: Cannot configure postcard when inband-telemetry is configured."

Which action resolves the issue?

Disable the telemetry feature

Disable the software-telemetry feature

Disable the hardware-telemetry feature

Disable the inband-telemetry feature

10. Refer to the exhibit.

A PC belongs to VLAN 68 The user experiences a large amount of packet loss when communicating with hosts that are outside of VLAN 68 .

Which action resolves the problem?

Replace HSRP with GLBP

Enable the peer-gateway feature

Remove the HSRP configuration

Configure ip arp synchronization on both switches.

Page 2 of 6

11. Refer to the exhibit.

A client configures an upgrade of its Cisco Nexus switches that are connected to the Cisco ACI controller, such that the switches are upgraded one at a time. After the upgrade is run, it is discovered that both Cisco Nexus switches were upgraded simultaneously .

Which two actions ensure that the switches upgrade one at a time? (Choose two.)

Configure the *Do not pause on failure and do not wait on cluster health" Run Mode

Choose the 'Pause upon upgrade failure" Run Mode

Select the "Graceful Maintenance" checkbox

Place each leaf switch in a different upgrade group

Check the Ignore Compatibility" checkbox

12. Refer to the exhibit.

A network engineer creates an EEM script to trigger an SNMP notification when a user enters configuration mode, but the trap is not received when the condition is met .

Which action resolves the issue?

Append action 2.0 event-default to the script

Append action 2.0 cli “conf t” to the script

Modify snmp-trap strdata “Configuration changed” to syslog msg Configuration changed

Modify cli match “conf t” to “snmp match “conf t”

13. An engineer must place a Cisco UCS B-Series Server in a single server pool in Cisco UCS Manager. The engineer creates a qualification policy, but the server is still seen in multiple pools .

Which two actions resolve the issue? (Choose two.)

Select the Server Pool Policy Qualification from the qualification drop-down menu in the Server Pool Policy

Select the Server Pool Policy from the qualification drop-down menu in the Server Pool Policy Qualification

Set the operating system qualifier inside the Server Pool Policy Qualification

Set the number of vNICs qualifier inside the Server Pool Policy.

Set the storage capacity qualifier inside the Server Poo. Policy Qualification.

14. Refer to the exhibit.

The EEM script overrides all events in the system policy .

What should be added to the script to resolve the issue?

event statement

environment variable

event-default action statement

configure terminal action

15. Refer to the exhibit.

A customer network uses OSPFv2 and MP-BGP protocols A network administrator installs a new Cisco Nexus Switch in the data center but experiences a BGP RIB failure.

Which action solves the issue?

Change the administrative distance of OSPF to 220

Configure the route as a BGP backdoor

Use a filter list for OSPF to filter both routes

Implement next-hop-self

16. An upgrade of protected RPMs from the Bash shell did not take effect .

Which action is required for the changes to take effect?

Restart the Bash shell.

Reload the switch.

Upgrade the RPMs from the Guest shell.

Disable and reenable the Bash feature.

17. An engineer removes a VMM domain from an endpoint group called EPG-1, but the distributed port group fails to be deleted .

Which action must be taken to resolve the issue?

Remove the port group manually.

Migrate all virtual machines in the EPG-1 to different hypervisors.

Remove the remaining EPGs from the VMM domain.

Migrate all virtual machines in the EPG-1 to different port groups.

18. A request to activate the port security database is rejected .

Which action do you perform to investigate the cause of the issue?

Enable the auto-learning feature.

Use the force option to identify rejected devices.

Find conflicting entries between the active and configuration databases.

Verify that devices are fully attached to the active database.

19. A Cisco UCSB-Series Blade Server is configured to boot a VMwareESXi host from an EMC VNX storage array by using a Fibre Channel SAN. The boot order is confirmed to be configured as expected but the server fails to boot from the SAN .

Which action reserves the problem?

Set the same WWPN pools for vHBA adapters

Set the boot LUN to the highest LUN ID in the storage array

Set the boot LUN to the lowest LUN ID in the storage array

Set the same WWNN pools for vHBA adaptor

20. Refer to the exhibit.

An OSPF adjacency between Router-A and Router-B cannot reach the FULL state .

Which action resolves the issue?

Adjust the MTU on Router-A to 1600.

Disable the check of the MTU value.

Set the OSPF media type to point-to-point.

Adjust the MTU on Router-B to 1604.

Page 3 of 6

21. Refer to the exhibit.

An engineer troubleshoots the HSRP configuration and notes that the remote end uses HSRP version 1. The engineer sets the local HSRP to version 1, but the problem continues .

Which action resolves the issue?

Change the local group number to 255 or less and request that the remote data center matches the group member in its configuration.

Set the local group number as 300 in the remote data center configuration

Run version 1 and version 2 HSRP on VLAN300 in the local data center.

Reduce the priority of the local HSRP to below 100 to force the local HSRP to standby and then change the version to version 1.

22. A server fails to boot from the operating system after a RAID1 cluster migration. The RAID remains in an inactive state during and after a service profile association .

Which action resolves the issue?

Configure the SAN boot target in the service profile.

Configure the SAN boot target to any configuration mode.

Use a predefined local disk configuration policy.

Remove the local disk configuration policy.

23. Cisco Unified Computing System Manager raises a critical error message that indicates that the system has overlapping Ethernet and FCoE VLANs. All of the Ethernet traffic on the overlapping VLANs drops .

Which action resolves the issue?

Modify the VLAN assignment to vNICs.

Change the PIN groups on the vHBAs.

Modify the FCoE VLA

Set the FCoE VLAN as the native VLAN on server uplinks.

24. An engineer must configure Linux hosts that are deployed on Cisco UCS B-Series Servers to boot from SAN. The SAN boot policy is configured in Cisco UCS Manager, and the boot order is verified to be set as expected However, the Linux hosts fail to boot .

Which action resolves the issue?

Remove all of the local storage that is installed

Delete and reconfigure the pWWN of the SAN boot target

Remove all of the ISO images that are mounted as a virtual CD-ROM

Delete and reconfigure the boot LUN

25. An engineer discovers that an NPV/NPIV uplink experiences a heavy load and plans to add more uplinks .

Which statement about what occurs when the new uplinks are added is true?

Only new connections use the new uplinks automatically.

Paths must be defined before new connections can use the new uplinks.

All connections must be reset before the new uplinks can be used.

New and existing connections use the new uplinks automatically.

26. An attempt to use a global vNIC redundancy template pair results in a service profile that fails to apply .

Which action resolves the issues?

Create the peer names before creating the templates.

Assign the secondary template first, and then set the peer name.

Assign both templates simultaneously.

Assign the primary template first, and then set the peer name.

27. A mission-critical server is connected to site A. Connectivity to this server is lost from site B because the MAC route is missing in the OTV VDC of the Nexus 7000 in site B due to MAC aging .

Which action allows the flooding of the unknown unicast MAC on the Nexus 7000 in the OTV VDC?

Use route-map to advertise this MAC statically and redistribute with ISI

Unknown unicast flooding is not allowed.

Use the otv flood mac <> command to selectively flood traffic for a given MA

Use the otv isis bfd <> command to configure BFD protocol.

28. Refer to the exhibit.

A new Cisco Nexus 5548 Switch connects to a network. SAN switching is configured on the switch. The switch fc2/10 NP uplink is shown in the exhibit .

Which action ensures that fc2/10 is in an up state?

Replace the SFP port module in fc2/10.

Configure the admin port type E on the upstream switch that connects the port.

Enable NPIV on the upstream switch that connects the port.

Configure the BB_credit buffers on the upstream switch that connects the port.

29. Refer to the exhibit.

Cisco UCS Manager is being upgraded using the Auto Install feature, but the FSM fails .

Which action resolves the issue?

Acknowledge the primary fabric interconnect.

Remove the service pack from the subordinate fabric interconnect.

Clear the startup version of the default infrastructure pack.

Upgrade the firmware of the infrastructure firmware by using the force option.

30. DRAG DROP

A firmware upgrade on a fabric interconnect fails. A bootflash contains a valid image.

Drag and drop the recovery steps from the left onto the correct order on the right.

Page 4 of 6

31. Refer to the exhibit.

The EEM script is applied in the default VDC to collect the outputs during high CPU utilization on the Cisco Nexus 7000 Series Switch for all VDCs .

Which configuration set must be added to the script to fix the issue?

switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli enable switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

switch(config-apple)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli enable switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

switch(config-apple)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli config t switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli config t switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

32. Refer to the exhibit.

A network engineer configures an EEM script to get a syslog notification after a configuration change. This message appears when the engineer must make a new configuration to this switch .

Which configuration did the engineer neglect to apply in the script for it to function properly?

event cli match ‘configure terminal’

event policy-default count 1 time 100

event syslog occurs 10

action 2.0 event-default

33. Refer to the exhibit.

An engineer is investigating a role mapping issue on a switch. The users report that they cannot view the IP addresses under the tenant “corp” .

Which action resolves the issue?

Add the users to the RADIUS server.

Update the UNIX I

Configure the correct secret password between the APIC and the RADIUS server.

Add the updated avpair to include/corp/admin/

34. Refer to the exhibit.

An engineer is troubleshooting the connectivity between Server-1 and Server-2 .

Which action resolves the connectivity issue?

Enable BGP advertise pip feature on both leaf switches

Configure the same source IP address on NVE and virtual peer link on leaf switches

Classify CFS messages for strict priority queue on spine switches

Change all ports on spine switches as port-type fabric

35. A system administrator connects a Cisco Nexus 2248PQ FEX to a fabric interconnect to expand the ports that are available for connecting Cisco UCS C-Series Rack Servers. In Cisco UCS Manager, the administrator does not see the servers connected to this FEX .

Which action should be taken to resolve the issue?

The FEX must be exchanged so that it supports the connectivity between fabric interconnects and UCS CSeries servers

The fabric interconnects must be rebooted before the FEX is recognized

The transceivers must be exchanged to support the connectivity between the FEX and the fabric interconnects

The ports that connect the FEX to the fabric interconnects must be configured as server ports

36. Refer to the exhibit.

vPC between switch1 and switch2 is not working .

Which two actions are needed to fix the problem? (Choose two.)

Match vPC domain ID between the two devices.

Configure IP address on the interface.

Activate VLANs on the vP

Configure vPC peer link and vPC peer keepalive correctly.

Configure one of the switches as primary for the vP

37. Refer to the exhibit.

A network administrator must delete a feature group from a Cisco Nexus 5000 Series Switch .

Which action resolves the issue?

Detach the association with the no rule command within the role configuration mode

Detach the association with the no role command within the feature-group configuration mode

Detach the association with the no rule command within the feature-group configuration

Detach the association with the no role command within the role configuration mode

38. The external routes fail to propagate to leaf switches in Cisco ACI fabric.

Which two actions resolve the issue? (Choose two.)

Enable the VTEP pool in the fabric

Assign an MP-BGP AS number to the fabric.

Specify the spine nodes as route reflectors

Associate the correct contract to the L30ut.

Configure an MP-BGP area.

39. Refer to the exhibit.

An engineer configures the server port on a Cisco Nexus 5000 Series Switch. The switch connects to an NPV edge switch port. The server fails to send the FC traffic to the fabric .

Which action resolves the issue?

Enable the NPIV mode on the Cisco Nexus 5000 switch.

Match the VSAN membership on both ends of the connection.

Configure the BB_credit buffer on the uplink port.

Replace the SFP in slot fc2/12.

40. An engineer is troubleshooting a fabric discovery failure .

Which two requirements must an engineer verify about switch connectivity to solve the problem? (Choose two.)

A Cisco APIC must be attached to a spine node only.

A Cisco APIC must be attached to leaf nodes.

Spine nodes must connect to other spine nodes.

A Cisco APIC must be dual-attached to two separate spine nodes.

Leaf nodes must connect to spine nodes only.

Page 5 of 6

41. Refer to the exhibit.

Partial configuration from N9K-1 and N9K-2 is included.

The client has two WANs connected.

✑ WAN-1 is for normal business-day activities.

✑ WAN-2 is for server backups during nonworking hours of 1:00 a.m. to 5:00 a.m. daily.

The client says that at the scheduled time for backup, the data center server failed to use the WAN-2 link to back up the servers to the cloud backup system .

What is the solution to this problem?

The event timer must be written in epoch time format.

The Cisco Nexus switch must be configured with one applet because a configuration with two applets will fail.

The Cron entry must be configured without double quotes.

The applet called “Backup” must include an action to remove the current static route.

42. An engineer must upgrade all components in a Cisco UCS domain to the same package version, but the upgrade process fails to complete .

Which set of Auto Install actions resolves the problem?

Install Infrastructure Firmware, then Install Server Firmware.

Install infrastructure Firmware, then Install Hypervisor Firmware.

Install Hypervisor Firmware, then Install Infrastructure Firmware

Install Server Firmware, then Install Infrastructure Firmware

43. Refer to the exhibit.

An engineer deploys SAN environment with two interconnected Cisco MDS 9000 Series switches. When the engineer attempts a zone merge, it fails with the error that is presented in the exhibit .

Which action resolves the issue?

Import or export a zone set between the switches to synchronize the switches.

Change the name of one of the zones to match the other zone set.

Set the distribute policy of the zone to full.

Ensure that the zone members have different names.

44. Refer to the exhibit.

An engineer is configuring boot from iSCSI on a Cisco UCS B-Series Blade Server, but the LUN fails to mount .

Which action resolves the issue?

Statically configure the target information in the Boot Policy.

Configure an MTU size of 9000 on the appliance port.

Configure a QoS policy on the vNI

Set a connection timeout value of 250 in the iSCSI Adapter Policy.

45. Refer to the exhibit.

An engineer is experiencing a problem when running a Docker container inside the Cisco Nexus 9000 bash shell .

Which action resolves the issue?

Add a new nameserver

Connect to bash as a different user

Change VRF to management

Configure the mgmt0 interface

46. An IOM fails during a firmware upgrade and is unresponsive .

Which action recovers the module?

Restore UCSM configuration from backup.

Roll back to the previous firmware.

Use AutoInstall to reinstall the firmware.

From the peer IOM, reset the faulty module.

47. Refer to the exhibit.

A Cisco UCS B-Series Blade Server is configured to boot from a shared storage via an iSCSI network. When a service profile is associated with the blade, the blade fails to attach the LUN .

Which action resolves the issue?

Place VLAN 0 on the interface that connects to the storage

Implement a Layer 3 connection between the blade and the storage

Establish a Layer 2 connection between the blade and the storage

48. Refer to the exhibit.

Sw1 and Sw2 are two Cisco Nexus 9000 Series Switches that run Cisco NX-OS. They are VTEPs in the same vPC domain .

Which statement describes what happens in this scenario?

Sw1 drops all traffic because there is no (S, G) OIF list to encapsulate VXLAN multicast packets and send them out to the underlay network through the uplink interfaces.

Sw1 performs the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs.

Sw1 and switch 2 perform the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs, depending on the hashing.

Sw2 did not send an IP PIM register to the rendezvous point for the multicast group of the VXLAN VN

49. Refer to the exhibit.

RBAC is configured on the MDS switch for a new SAN administrator engineer to work on the FSPF configuration. However, after the configuration is applied the engineer who was assigned the FSPF_Admin role cannot perform any configuration changes .

Which action resolves the issue?

Write rule 2 before rule 1

Remove rule 1 from the role

Configure the switch license for RBAC

Reload the switch

50. Refer to the exhibit.

A network engineer deploys scripts to the guest shell of a Cisco Nexus switch. The scripts fail to operate properly due to the limited CPU and file system resources that are assigned by default to the guest shell. The engineer allocated more memory and disk space to the guest shell, but the application continues to fail .

Which action resolves the issue?

Disable and enable bash shell

Reboot the guest shell

Redeploy the bash shell

Upgrade the guest shell

Page 6 of 6

51. Refer to the exhibit.

The HSRP instance on both switches is showing as active .

Which action resolves the issue?

Configure the HSRP timers to be the same.

Allow VLAN 100 between the switches.

Configure the IP address of N9K-B on the same subnet as N9K-

Configure preempt on only one of the switches.

52. An engineer is troubleshooting a custom AV pair that was created by a client on an external authentication server to map a read-only role for a specific security domain .

Which AV pair solves the problem?

shell:domains=Security_Domain_1//Read_Role_1|Read_Role_2

shell:domains=Security_Domain_1/Write_Role_1|Read_Role_2

shell=Security_Domain_1/Read_Role_1|Read_Role_2

shell:domains=Security_Domain_1/Read_Role_1|Read_Role_2

300-615 DCIT CCNP Data Center Updated Questions Available

300-615 DCIT CCNP Data Center Updated Questions Available

Share this post

Leave a Reply Cancel reply

Related Posts