Fortinet NSE 7 NSE7_SDW-7.0 Exam Dumps

dumps2023-11-16T16:59:01+08:00

The NSE7_SDW-7.0 exam is a hot one for Fortinet NSE 7 certification. There are 35 questions in real Fortinet NSE7_SDW-7.0 exam, and you have 60 minutes to answer all the questions. The available languages are English and Japanese. We provide the latest Fortinet NSE 7 NSE7_SDW-7.0 exam dumps, which are the best material for you to test the following topics: SD-WAN configuration, Centralized management, Advanced IPsec VPN, SD-WAN troubleshooting. Free Fortinet NSE7_SDW-7.0 exam dumps are below.

Page 1 of 3

1. Which diagnostic command can you use to show the member utilization statistics measured by performance SLAs for the last 10 minutes?

diagnose sys sdwan intf-sla-log

diagnose sys sdwan health-check

diagnose sys sdwan log

diagnose sys sdwan sla-log

2. Which two protocols in the IPsec suite are most used for authentication and encryption? (Choose two.)

Encapsulating Security Payload (ESP)

Secure Shell (SSH)

Internet Key Exchange (IKE)

Security Association (SA)

3. Which two settings can you configure to speed up routing convergence in BGP? (Choose two.)

update-source

set-route-tag

holdtime-timer

link-down-failover

4. Refer to the exhibits.

Exhibit A

Exhibit B -

Exhibit A shows the configuration for an SD-WAN rule and exhibit B shows the respective rule status, the routing table, and the member status.

The administrator wants to understand the expected behavior for traffic matching the SD-WAN rule. Based on the exhibits, what can the administrator expect for traffic matching the SD-WAN rule?

The traffic will be load balanced across all three overlays.

The traffic will be routed over T_INET_0_0.

The traffic will be routed over T_MPLS_0.

The traffic will be routed over T_INET_1_0.

5. Refer to the exhibits.

Two hub-and-spoke groups are connected through a site-to-site IPsec VPN between Hub 1 and Hub 2. The administrator configured ADVPN on both hub-and-spoke groups.

Which two outcomes are expected if a user in Toronto sends traffic to London? (Choose two.)

London generates an IKE information message that contains the Toronto public IP address.

Traffic from Toronto to London triggers the dynamic negotiation of a direct site-to-site VP

Toronto needs to establish a site-to-site tunnel with Hub 2 to bypass Hub 1.

The first packets from Toronto to London are routed through Hub 1 then to Hub 2.

6. Which two performance SLA protocols enable you to verify that the server response contains a specific value? (Choose two.)

http

icmp

twamp

dns

7. Refer to the exhibits.

Which two conclusions for traffic that matches the traffic shaper are true? (Choose two.)

The traffic shaper drops packets if the bandwidth is less than 2500 KBps.

The measured bandwidth is less than 100 KBps.

The traffic shaper drops packets if the bandwidth exceeds 6250 KBps.

The traffic shaper limits the bandwidth of each source IP to a maximum of 6250 KBps.

8. Refer to the exhibit.

Which configuration change is required if the responder FortiGate uses a dynamic routing protocol to exchange routes over IPsec?

type must be set to static.

mode-cfg must be enabled.

exchange-interface-ip must be enabled.

add-route must be disabled.

9. Which CLI command do you use to perform real-time troubleshooting for ADVPN negotiation?

get router info routing-table all

diagnose debug application ike

diagnose vpn tunnel list

get ipsec tunnel list

10. Refer to the exhibits.

Exhibit B

Exhibit A shows the system interface with the static routes and exhibit B shows the firewall policies on the managed FortiGate.

Based on the FortiGate configuration shown in the exhibits, what issue might you encounter when creating an SD-WAN zone for port1 and port2?

port1 is assigned a manual IP address.

port1 is referenced in a firewall policy.

port2 is referenced in a static route.

port1 and port2 are not administratively down.

Page 2 of 3

11. Which two statements are correct when traffic matches the implicit SD-WAN rule? (Choose two.)

The sdwan_service_id flag in the session information is 0.

All SD-WAN rules have the default setting enabled.

Traffic does not match any of the entries in the policy route table.

Traffic is load balanced using the algorithm set for the v4-ecmp-mode setting.

12. Refer to the exhibit.

An administrator is troubleshooting SD-WAN on FortiGate. A device behind branch1_fgt generates traffic to the 10.0.0.0/8 network. The administrator expects the traffic to match SD-WAN rule ID 1 and be routed over T_INET_0_0. However, the traffic is routed over T_INET_1_0.

Based on the output shown in the exhibit, which two reasons can cause the observed behavior? (Choose two.)

The traffic matches a regular policy route configured with T_INET_1_0 as the outgoing device.

T_INET_1_0 has a lower route priority value (higher priority) than T_INET_0_0.

T_INET_0_0 does not have a valid route to the destination.

T_INET_1_0 has a higher member configuration priority than T_INET_0_0.

13. Refer to the exhibit.

Based on the exhibit, which two actions does FortiGate perform on sessions after a firewall policy change? (Choose two.)

FortiGate flushes all sessions.

FortiGate terminates the old sessions.

FortiGate does not change existing sessions.

FortiGate evaluates new sessions.

14. Which two statements about SD-WAN central management are true? (Choose two.)

The objects are saved in the ADOM common object database.

It does not support meta fields.

It uses templates to configure SD-WAN on managed devices.

It supports normalized interfaces for SD-WAN member configuration.

15. Refer to the exhibits.

Which conclusion about the packet debug flow output is correct?

The total number of daily sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the traffic shaper, and the packet was dropped.

The packet size exceeded the outgoing interface MT

The number of concurrent sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the traffic shaper, and the packet was dropped.

The number of concurrent sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the firewall policy, and the packet was dropped.

16. Which are two benefits of using CLI templates in FortiManager? (Choose two.)

You can reference meta fields.

You can configure interfaces as SD-WAN members without having to remove references first.

You can configure FortiManager to sync local configuration changes made on the managed device, to the CLI template.

You can configure advanced CLI settings.

17. What is the route-tag setting in an SD-WAN rule used for?

To indicate the routes for health check probes.

To indicate the destination of a rule based on learned BGP prefixes.

To indicate the routes that can be used for routing SD-WAN traffic.

To indicate the members that can be used to route SD-WAN traffic.

18. Refer to the exhibit.

The exhibit shows the SD-WAN rule status and configuration.

Based on the exhibit, which change in the measured latency will make T_MPLS_0 the new preferred member?

When T_INET_0_0 and T_MPLS_0 have the same latency.

When T_MPLS_0 has a latency of 100 ms.

When T_INET_0_0 has a latency of 250 ms.

When T_N1PLS_0 has a latency of 80 ms.

19. Refer to the exhibits.

Exhibit A -

Exhibit B -

Exhibit A shows the traffic shaping policy and exhibit B shows the firewall policy.

The administrator wants FortiGate to limit the bandwidth used by YouTube. When testing, the administrator determines that FortiGate does not apply traffic shaping on YouTube traffic.

Based on the policies shown in the exhibits, what configuration change must be made so FortiGate performs traffic shaping on YouTube traffic?

Destination internet service must be enabled on the traffic shaping policy.

Application control must be enabled on the firewall policy.

Web filtering must be enabled on the firewall policy.

Individual SD-WAN members must be selected as the outgoing interface on the traffic shaping policy.

20. Refer to the exhibit, which shows the IPsec phase 1 configuration of a spoke.

What must you configure on the IPsec phase 1 configuration for ADVPN to work with SD-WAN?

You must set ike-version to 1.

You must enable net-device.

You must enable auto-discovery-sender.

You must disable idle-timeout.

Page 3 of 3

21. Refer to the exhibits.

Exhibit A -

Exhibit B

Exhibit A shows a site-to-site topology between two FortiGate devices: branch1_fgt and dc1_fgt.

Exhibit B shows the system global and system settings configuration on dc1_fgt.

When branch1_client establishes a connection to dc1_host, the administrator observes that, on dc1_fgt, the reply traffic is routed over T_INET_0_0, even though T_INET_1_0 is the preferred member in the matching SD-WAN rule.

Based on the information shown in the exhibits, what configuration change must be made on dc1_fgt so dc1_fgt routes the reply traffic over T_INET_1_0?

Enable auxiliary-session under config system settings.

Disable tсp-session-without-syn under config system settings.

Enable snat-route-change under config system global.

Disable allow-subnet-overlap under config system settings.

Fortinet NSE 7 NSE7_SDW-7.0 Exam Dumps

Fortinet NSE 7 NSE7_SDW-7.0 Exam Dumps

Share this post

Leave a Reply Cancel reply

Related Posts