NACE-CIP2-001 Coating Inspector Level 2 Written Exam Dumps

dumps2021-12-21T01:48:41+08:00

NACE-CIP2-001 exam is the written test for NACE Coating Inspector Level 2 certification. The online NACE-CIP2-001 exam dumps are good and valid for each NACE candidate to take and pass the test. There are 100 multipl-choice questions in real NACE Coating Inspector Level 2 NACE-CIP2-001 exam, and you have 2 and 1/2 hours to finish the test. Besides, CIP Level 1 certification is prerequisites. Free Coating Inspector Level 2 written exam NACE-CIP2-001 dumps are available below.

Page 1 of 3

1. Thermal Spray coatings provide:

Barrier protection

Inhibitive protection

Sacrificial protection

Thermal protection

2. NACE International Standards are developed by:

Government mandates

International mandates

Standard committees

Regional mandates

3. Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be

washed with clean potable water prior to Use.

mixed with uncontaminated abrasive

run through the air wash separator.

disposed of properly.

4. Individuals conducting Coating Surveys should:

Always be NACE Level 3 Certified Inspectors

Always be NACE or SSPC Protective coating Specialists

Always be experienced Specification Writers

Always be trained and experienced Coating Industry

5. In which type of concrete are laitance commonly encountered?

Concrete block (poured with a form)

Gunite

Glass fiber cement

Poured (wet cast)

6. You are working as an inspector in a galvanizing plant for the first time.

What are some of the hazards you need to be aware of:

Risk of chemical exposure

Risk of skin

Risk of acid or caustic splashes

a), b), and c)

7. Coating Surveys are legally required:

On commercial marine vessels and offshore platforms

On high pressure gas lines and fireproofed structures

On water tanks and potable water pipelines

On food and beverage vessels and can linings

8. The Inspectors' goal at the Pre-Job Conference is to:

Obtain a clear understanding of the Specification

Discuss contractual requirements

Manage the meeting so it doesn't go off topic

Take accurate meeting minutes for distribution

9. When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:

Ultra Sonic DFT Gauge

Tooke Gauge

Eddy Current Gauge

Magnetic Gauge

10. External coatings applied to buried pipelines are generally tested for:

Gloss level

Chalking resistance

Cathodic disbondment

Solvent resistance

Page 2 of 3

11. Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?

Sacking

Acid etching

Stoning

High-pressure water washing

12. You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.

Your FIRST preferred course of action is to:

Refuse to take readings until an is in place

Develop your own methodology and proceed take the readings

Use a generally accepted industry standard and to take readings

Call your supervisor

13. You have just your NACE CIP Level 2 certification when you are asked to supervise a team of uncertified field pipeline inspectors.

Your FIRST preferred course of action is to:

Accept assignment without hesitation

Advise the prospective employer that you cannot accept the position

Meet with the prospective employer to scope of your role

Review the NACE Attestation prior to making a decision

14. Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.

True

False

15. The Concrete Repair Institute's comparators can be used to assess:

Surface cleanliness prior to coating

Surface profile prior to coating

Contamination levels prior to coating

Compressive and tensile strength prior to coating

16. When performing inspection in accordance with ASTM D 4138 the Inspector will use:

A set of 14 pencils of varying hardness

A destructive paint inspection Tooke gauge

A mechanical adhesion tester

A hardness tester

17. You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method. At the pre-job meeting operations personnel make it clear that abrasive blasting will not permitted. The Owner's representative asks you what other methods might be used.

Of the options shown below, what would be the preferred option in this situation?

SP 1 followed by acid etching

SP 1 followed by caustic etching

SP 1 followed by SP 2

SP 1 followed by SP 3

18. Which standards are generally established by private-sector bodies and are available for use by any person or Organization, private or government?

Consensus

Mandatory

De facto

Voluntary

19. Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires

25 single rubs with a saturated cloth.

35 single rubs with a saturated cloth.

50 double rubs with a saturated cloth.

25 double rubs with a saturated cloth.

20. The most likely area of failure on a buried external pipeline coating is the:

Mainline coating

Field joint coating

Areas exposed to Ultra Violet light

Ground bed

Page 3 of 3

21. Ideally, documentation requirements should be defined:

At the pre-job conference

In the specification

By the inspector

By the contractor

22. In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?

Flow stage

Wetting stage

Cure stage

Gel stage

23. NACE Standards include:

Standard Practices

Material Requirements

a) & b)

a) only

24. Non-Conformance Reports are designed to:

Punish the Contractor for substandard work

Elevate the status of the Inspector

Assist the Owner in negotiating credits from the Contractor

To identify items that do not meet the specification requirements

25. You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.

Your FIRST preferred course of action is to:

Check to See if the dehumidification equipment is operating correctly

Call your supervisor

Advise the coating applicator supervisor of your readings

Document the readings at the end of the shift

26. When completing the Final Inspection report the Inspector should write the report using:

Language that only technical experts would understand

Language that the most would understand

Language that only in the project would understand

Language that another NACE Inspector would understand

27. The standards defining surface cleanliness achieved by centrifugal blast cleaning are:

Different than air blast cleaning

The same as air blast cleaning

Slightly different to air blast cleaning

Comparable to air blast cleaning

28. An Inspection and Test Plan is required when:

It is always required

When the Coating Applicator requests one

When the Owner specifies one

When the Inspector requests one

29. Cold-applied tape

are identifiable by its distinct colors, usually light blue, green, Or Grey.

is typically green or led and looks like “painted" finish.

have a cross-linked polyethylene backing and a heat-activated adhesive.

is polyethylene film, heat laminated, 'With an adhesive layer of butyl glue.

30. Examples of non-ferrous metals include

Select All that Apply:

mild steel.

aluminum

iron

copper

Comments (6)

Abhishek August 5, 2022 Reply

I want to buy the dumps but want to pay in INR . Pls suggest how to pay in INR
- dumps August 6, 2022 Reply
  
  Hi, you can use your Credit Card to pay it. It is very convenient.
  
  Regards,
  Lily
Chathura Pererta May 5, 2022 Reply

4. Individuals conducting Coating Surveys should:

Correct answer should be : Always be trained and experienced Coating Industry
- dumps May 6, 2022 Reply
  
  Thanks for your correction.
Tomas Alcantara February 14, 2022 Reply

I have order but I have an error when I try to popen the file, please help me
- dumps February 15, 2022 Reply
  
  Please tell the details of the error.