NSE7_NST-7.2 Fortinet NSE 7 - Network Security 7.2 Support Engineer Exam Free Dumps - Free Latest Dumps for IT Certification Exams

NSE7_NST-7.2 Fortinet NSE 7 – Network Security 7.2 Support Engineer Exam Free Dumps

dumps2024-06-15T09:34:36+08:00

NSE7_NST-7.2 Fortinet NSE 7 – Network Security 7.2 Support Engineer exam is the elective test for FCSS in Network Security certification. There are 40 multiple-choice questions in the real Fortinet NSE7_NST-7.2 exam, and you have 75 minutes to answer all the questions. The pass or fail report is available from your Pearson VUE account. We provide the latest Fortinet NSE 7 – Network Security 7.2 Support Engineer NSE7_NST-7.2 exam dumps, which can guarantee you pass easily. Free FCSS in Network Security NSE7_NST-7.2 exam dumps are available below.

Page 1 of 2

1. Refer to the exhibit, which shows the omitted output of a real-time OSPF debug

Which statement is false?

A password has been configured on the local OSPF router but is not shown in the output

The Hello packet is being sent from an OSPF router with ID 0.0.0.112.

The two FortiGate devices attempting adjacency are in area 0.0.0.0.

One FortiGate device is configured to require authentication, while the other is not

2. Which of the following regarding protocol states is true?

proto_state=00 indicates that UDP traffic flows in both directions.

proto_state-01 indicates an established TCP session.

proto_state=10 indicates an established TCP session.

proto state=01 indicates one-way ICMP traffic.

3. Which statement is correct regarding LDAP authentication using the regular bind type?

The regular bind type goes through four steps to successfully authenticate a user.

The regular bind type cannot be used if users are authenticated using sAMAccountName.

The regular bind type is the easiest bind type to configure on FortiO

The regular bind type requires a FortiGate super_admin account.

4. Refer to the exhibit.

FortiGate has already been configured with a firewall policy that allows all ICMP traffic to flow from port1 to port3.

Which changes must the administrator perform to ensure the server at 10.4.0.1/24 receives the echo reply from the laptop at 10.1.0.1/24?

Enable asymmetric routing under config system settings.

Modify the default gateway on the laptop from 10.1.0.2 to 10.2.0.2

A firewall policy that allows all ICMP traffic from port3 to port1.

Change the configuration from strict RPF check mode to feasible RPF check mode

5. Which two conditions would prevent a static route from being added to the routing table? (Choose two.)

The next-hop IP address is unreachable.

The interface specified in the route configuration is down

The route has a lower priority value than another route to the same destination.

There is another other route to the same destination, with a lower distance.

6. Refer to the exhibit, which shows a truncated output of a real-time RADIUS debug.

Which two statements are true? (Choose two.)

The RADIUS server queried for authentication is located at IP address 172.25.188.164.

Authentication was unsuccessful.

The authentication scheme used was pop3.

Authentication was successful

Two-factor authentication was required.

7. Which three conditions are required for two FortiGate devices to form an OSPF adjacency? (Choose three.)

OSPF link costs match.

OSPF interface priority settings are unique

OSPF interface network types match

Authentication settings match.

OSPF router IDs are unique.

8. Refer to the exhibit, which contains the partial output of a diagnose command.

Based on the output, which two statements are correct? (Choose two.)

The remote gateway IP is 10.200.5.1.

The remote gateway has quick more selectors containing a destination subnet of 10.1.2.0/24.

DPD is disabled.

Anti-replay is enabled.

9. Refer to the exhibit, which shows a session table entry.

Which statement about FortiGate behavior relating to this session is true?

FortiGate forwarded this session without any inspection.

FortiGate is performing a security profile inspection using the CP

FortiGate redirected the client to the captive portal to authenticate, so that a correct policy match could be made.

FortiGate applied only IPS inspection to this session.

10. What is the diagnose test application ipsmonitor 5 command used for?

To disable the IPS engine

To provide information regarding IPS sessions

To restart all IPS engines and monitors

To enable IPS bypass mode

Page 2 of 2

11. Refer to the exhibit.

Refer to the exhibit, which shows the modified output of the routing kernel.

Which statement is true?

The BGP route to 10.0.4.0/24 is not in the forwarding information base.

The default static route through port2 is in the forwarding information base.

The default static route through 10.200.1.254 is not in the forwarding information base.

The egress interface associated with static route 8.8.8.8/32 is administratively up.

12. Refer to the exhibits, which show the configuration on FortiGate and partial session information for internet traffic from a user on the internal network.

If the priority on route ID _ were changed from 10 to 0, what would happen to traffic matching that user session?

The session would be deleted, and the client would need to start a new session.

The session would remain in the session table, but its traffic would now egress from both port1. andport2.

The session would remain in the session table, and its traffic would egress from port2.

The session would remain in the session table, and its traffic would egress from port1.

NSE7_NST-7.2 Fortinet NSE 7 – Network Security 7.2 Support Engineer Exam Free Dumps

NSE7_NST-7.2 Fortinet NSE 7 – Network Security 7.2 Support Engineer Exam Free Dumps

Share this post

Leave a Reply Cancel reply

Related Posts